东莞忠业塑胶
忠业塑胶

专业工程塑料、塑胶原料经营商

全国服务热线

13829200144

塑胶原料
塑胶原料wap
当前位置:塑料经营商 >> 产品展示 >> PC塑胶原料 >> PC1414 SABIC EXL1414/沙伯基础(GE)耐候塑料
PC1414 SABIC  EXL1414/沙伯基础(GE)耐候塑料

PC1414 SABIC EXL1414/沙伯基础(GE)耐候塑料

PC1414 SABIC EXL1414/沙伯基础(GE)耐候塑料

全国24小时销售热线:

13829200144
产品介绍

PC1414 SABIC  物性资料

  • 规格用途

  • 规格级别其它 其它 其它外观颜色
    该料用途
    备注说明
  • 技术参数

  • 性能项目试验条件[状态]测试方法测试数据数据单位
    物理性能密度
    ISO 11831.19g/cm
    成型收缩率-,水平方向
    0.4-0.8%
    -,垂直方向
    0.4-0.8%
    吸水率
    ISO 620.35%
    机械性能屈服拉伸强度
    ASTM D63855MPa
    拉伸强度
    ASTM D63850MPa
    断裂伸长率
    ASTM D63898%
    屈服伸长率
    ASTM D6386%
    弯曲强度
    ASTM D79092MPa
    弯曲模量
    ASTM D7902230MPa
    洛氏硬度
    ASTM D785121R
    Izod缺口冲击强度23℃ASTM D256865J/m
    -30℃ASTM D256774J/m
    电气性能体积电阻率
    ASTM D257>1.E+15Ohm.cm
    表面电阻率
    ASTM D257>1.E+15Ohm
    相对电阻率100HzASTM D1502.68
    介电消散因子100HzASTM D1500.0012
    热性能维卡软化温度
    ASTM D1525145
    热变形温度-,0.45MpaASTM D648139
    -,1.82MpaASTM D648124

英文PC1414物性资料

TYPICAL PROPERTIES (1)
MECHANICALValueUnitStandard
Tensile Stress, yld, Type I, 50 mm/min560kgf/cm2ASTM D 638
Tensile Stress, brk, Type I, 50 mm/min510kgf/cm2ASTM D 638
Tensile Strain, yld, Type I, 50 mm/min6%ASTM D 638
Tensile Strain, brk, Type I, 50 mm/min98%ASTM D 638
Tensile Modulus, 50 mm/min20500kgf/cm2ASTM D 638
Flexural Stress, yld, 1.3 mm/min, 50 mm span940kgf/cm2ASTM D 790
Flexural Modulus, 1.3 mm/min, 50 mm span22700kgf/cm2ASTM D 790
Hardness, Rockwell L89-ASTM D 785
Hardness, Rockwell R121-ASTM D 785
Tensile Stress, yield, 50 mm/min57MPaISO 527
Tensile Stress, break, 50 mm/min60MPaISO 527
Tensile Strain, yield, 50 mm/min6%ISO 527
Tensile Strain, break, 50 mm/min120%ISO 527
Tensile Modulus, 1 mm/min2150MPaISO 527
Flexural Stress, yield, 2 mm/min85MPaISO 178
Flexural Modulus, 2 mm/min2250MPaISO 178
IMPACTValueUnitStandard
Izod Impact, notched, 23°C88cm-kgf/cmASTM D 256
Izod Impact, notched, -30°C78cm-kgf/cmASTM D 256
Instrumented Impact Total Energy, 23°C714cm-kgfASTM D 3763
Izod Impact, unnotched 80*10*3 +23°CNBkJ/m2ISO 180/1U
Izod Impact, unnotched 80*10*3 -30°CNBkJ/m2ISO 180/1U
Izod Impact, notched 80*10*3 +23°C70kJ/m2ISO 180/1A
Izod Impact, notched 80*10*3 -30°C60kJ/m2ISO 180/1A
Charpy 23°C , V-notch Edgew 80*10*3 sp=62mm70kJ/m2ISO 179/1eA
Charpy -30°C , V-notch Edgew 80*10*3 sp=62mm65kJ/m2ISO 179/1eA
Charpy 23°C , Unnotch Edgew 80*10*3 sp=62mmNBkJ/m2ISO 179/1eU
Charpy -30°C , Unnotch Edgew 80*10*3 sp=62mmNBkJ/m2ISO 179/1eU
THERMALValueUnitStandard
Vicat Softening Temp, Rate B/50145°CASTM D 1525
HDT, 0.45 MPa, 3.2 mm, unannealed139°CASTM D 648
HDT, 1.82 MPa, 3.2mm, unannealed124°CASTM D 648
CTE, -40°C to 40°C , flow6.96E-051/°CASTM E 831
CTE, -40°C to 40°C , xflow7.47E-051/°CASTM E 831
CTE, 23°C to 80°C , flow7.2E-051/°CISO 11359-2
CTE, 23°C to 80°C , xflow7.2E-051/°CISO 11359-2
Ball Pressure Test, 125°C +/- 2°CPasses-IEC 60695-10-2
Vicat Softening Temp, Rate B/50145°CISO 306
Vicat Softening Temp, Rate B/120146°CISO 306
HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm140°CISO 75/Be
HDT/Ae, 1.8 MPa Edgew 120*10*4 sp=100mm128°CISO 75/Ae
Relative Temp Index, Elec130°CUL 746B
Relative Temp Index, Mech w/impact120°CUL 746B
Relative Temp Index, Mech w/o impact125°CUL 746B
PHYSICALValueUnitStandard
Specific Gravity1.18-ASTM D 792
Mold Shrinkage, flow, 3.2 mm0.4 - 0.8%SABIC Method
Mold Shrinkage, xflow, 3.2 mm0.4 - 0.8%SABIC Method
Melt Flow Rate, 300°C /1.2 kgf10g/10 minASTM D 1238
Density1.19g/cm2ISO 1183
Water Absorption, (23°C /sat)0.35%ISO 62
Moisture Absorption (23°C / 50% RH)0.15%ISO 62
Melt Volume Rate, MVR at 300°C /1.2 kg9cm3/10 minISO 1133
ELECTRICALValueUnitStandard
Volume Resistivity>1.E+15Ohm-cmASTM D 257
Surface Resistivity>1.E+15OhmASTM D 257
Dielectric Strength, in oil, 0.8 mm16.2kV/mmASTM D 149
Relative Permittivity, 100 Hz2.68-ASTM D 150
Relative Permittivity, 1 MHz2.64-ASTM D 150
Dissipation Factor, 100 Hz0.0012-ASTM D 150
Dissipation Factor, 1 MHz0.0093-ASTM D 150
FLAME CHARACTERISTICSValueUnitStandard
UL Recognized, 94HB Flame Class Rating (3)0.4mmUL 94
Glow Wire Flammability Index 850°C , passes at0.8mmIEC 60695-2-12
Glow Wire Flammability Index 960°C , passes at1mmIEC 60695-2-12
Glow Wire Ignitability Temperature, 1.0 mm875°CIEC 60695-2-13
Glow Wire Ignitability Temperature, 3.0 mm875°CIEC 60695-2-13
Processing


Parameter
Injection MoldingValueUnit
Drying Temperature120°C
Drying Time3 - 4hrs
Drying Time (Cumulative)48hrs
Maximum Moisture Content0.02%
Melt Temperature295 - 315°C
Nozzle Temperature290 - 310°C
Front - Zone 3 Temperature295 - 315°C
Middle - Zone 2 Temperature280 - 305°C
Rear - Zone 1 Temperature215 - 295°C
Mold Temperature70 - 95°C
Back Pressure0.3 - 0.7MPa
Screw Speed40 - 70rpm
Shot to Cylinder Size40 - 60%
Vent Depth0.025 - 0.076mm


相关产品